ACS

The Advanced Camera for Surveys (ACS) was installed in Hubble by the crew of the Space Shuttle Columbia (STS-109) during Servicing Mission 3B, which took place March 1 to March 12, 2002. With its wide field of view, superb image quality, and exquisite sensitivity, the Advanced Camera for Surveys (ACS) has 10 times more discovery power than the camera it superceded (WFPC 2). ACS became mostly inoperable in January 2007, but is slated for repairs in SM4.

FGS

The Fine Guidance Sensors (FGS) are optical sensors used on the Hubble Space Telescope to provide pointing information for the spacecraft and also as a scientific instrument for astrometric science.

An FGS houses a collection of mirrors, lenses, servos, prisms, beam-splitters and photomultiplier tubes.

There are three fine guidance sensors on Hubble located at 90-degree intervals around the circumference of the telescope. Two FGSs are used to lock onto "guide stars" and point the telescope at an astronomical target, and hold that target in a scientific instrument's field of view. The third FGS can then be used as a scientific instrument for astrometry.

NICMOS

The Near Infrared Camera and Multi-Object Spectrometer (NICMOS) provides imaging capabilities in broad, medium, and narrow band filters, broad-band imaging polarimetry, coronographic imaging, and slitless grism spectroscopy, in the wavelength range 0.8-2.5 microns. NICMOS has three adjacent but not contiguous camera channels, each with a different field of view (FOV) on the sky.

STIS

The Space Telescope Imaging Spectrograph is a powerful general-purpose spectrograph. STIS was installed during Servicing Mission 2 on February 12, 1997. STIS performed on-orbit operations for approximately 65,000 hours (7 years, 171 days) before failing on August 3, 2004. The instrument remains in safe mode and will be repaired during SM4.

WFPC2

The Wide Field and Planetary Camera 2 (WFPC2), a second-generation imaging camera, was installed on Hubble during Servicing Mission 1 (SM1) in 1993. WFPC2 is an upgraded version of the telescope's original Wide Field and Planetary Camera 1 (WFPC1). In addition to providing internal optical corrections, WFPC2 significantly improved ultraviolet performance over WFPC1 and possessed more advanced detectors.

Batteries

Each of Hubble's six batteries consists of 22 cells in series along with heaters, heater controllers, pressure measurement transducers and electronics, and temperature-measuring devices and their associated electronics. Three batteries are packaged into modules measuring roughly 36 by 32 by 11 in. (91 x 81 x 28 cm) and weighing about 460 pounds (209 kg). Each of the two modules is equipped with two large yellow handles that astronauts use to maneuver the module in and out of the Telescope in space.

COSTAR

The Corrective Optical Space Telescope Axial Replacement (COSTAR) was developed as an effective means of countering the effects of the incorrect shape of Hubble's primary mirror. COSTAR is a telephone booth-sized instrument which placed three pairs of corrective mirrors, some as small as a nickel coin, in front of the Faint Object Camera (FOC), the Faint Object Spectrograph (FOS) and the Goddard High Resolution Spectrograph (GHRS).

Gyros

The Gyroscopes are part of Hubble's pointing system. They report any small movements of the spacecraft to Hubble's Pointing and Control System. The computers then command the spinning reaction wheels to maintain the spacecraft at the desired location. A complete set of gyrosopes is six in number, housed in three Rate Sensing Units (RSUs), each containing two gyros.

NOBL

Hubble is protected by multi-layer external blankets. They maintain normal operating temperatures of Hubble's electronic equipment. Some damage to these external blankets was discovered during the second servicing mission in 1997, and additional wear and tear has been seen in each subsequent visit to the telescope.

Starting with servicing mission 3A in 1999 astronauts began covering Hubble with permanent sheets called the New Outer Blanket Layer (NOBL). The NOBLs are designed to protect Hubble's external blankets and are specially coated stainless steel foil trimmed to fit each particular door. Each cover is supported by a steel picture-frame structure. Expanding plugs, like common kitchen bottle stoppers, fit into door vent holes to allow quick installation.

SIC&DH

The Science Instrument Control and Data Handler (SIC&DH) unit is a collection of electronic components attached to a tray mounted on the door of Bay 10 in the SSM Equipment Section. Components of the SIC&DH unit are: The NASA Standard Spacecraft Computer (NSCC-I); Two standard interface circuit boards for the computer; Two control unit/science data formatters (CU/SDF); Two CPU modules; A Power Control Unit; Two Remote Interface Units; And various memory, data and command communications lines (buses) connected by couplers. These components are redundant so the system can recover from any single failure.

Solar Arrays

The solar arrays (SA3) are rigid arrays, which do not roll up and therefore are more robust. Although one-third smaller than the first two pair (the original pair and the ones installed during SM1), they produce 30 percent more power. They are less susceptible to extreme temperatures and their smaller size reduces the effects of atmospheric drag on the spacecraft.